Punch List Details

back to overview

Specials & Forming Tools(Trumpf)

No picture saved.

DESCRIPTIONDIMENSIONSSTATION SIZETOOL NO.   
Bridge, Form-only (Form-Up) 1.000 wide x 3.022 L x 0.105 high. 45 degree angles. For .075 thick stainless. 3.00 632 WT #791800-10 for 400-0006-00  
Cluster Tool .093 Round 8x Round (0.093) 8x Cluster Assy for .062 Alum with replaceable inserts. 3.00 624 4x2 pattern .312 'x', .270 ‘y’  
Cluster Tool .105 Square 6x Square (0.105) 6x Cluster Assy. for .018" Crs. with replaceable inserts. 3.00 834 WT #1158930-10 for 80-10085+ R-A  
Cluster Tool .115 x .205 Obround 10x Obround .115 x .205 (10x) Cluster Assy. for .035" Crs. with replaceable inserts. 3.00 858 WT # for 203-12917-01 R-C  
Cluster Tool .133 Round 12x Round (0.133) 12x Cluster Assy. for .059" Crs. with replaceable inserts. 3.00 869 WT #1215506-10 for 40-10391-2+ R-1  
Cluster Tool .170 Hex 16x Hex 0.170 16x Cluster Assy for .035 CRS 3.00 445 4x4 pattern .390 ‘x’, .450 ‘y’  
Cluster Tool .177 Round 9x Round 4.5mm (0.177) 9x Cluster Assy. for .059 3.00 897 3x3 pattern 12mm 'x', 10mm 'y' WT #1308726-10  
Coined Logo “A” 0.38H x 0.30W Coin Down, .030 Deep for .125 material 3.00 434 WT #466-5849  
Coined Logo “B” 0.38H x 0.30W Coin Down, .030 Deep for .125 material 3.00 435 WT #466-5850  
Coined Logo - Up .625 Dia. Circle Coin Up, .020 Deep x .010 wide line, Chisel Point. 3.00 610 WT #757364-20  
Dash Tool – (Form-Down) 0.200 long 3.00 798 WT #1090844-10  
Dash Tool – (Form-Down) 0.500 long 3.00 315    
Dash Tool – (Form-Up) 0.500 long 3.00 417    
Dimple .030 Rad. Form-Down .015 Deep. Relieved for .550 center to center between dimples. .035 material 3.00 218 Mate 11039130  
Dimple .060 Dia. Form-Up .015 High .090 material 3.00 263 Mate #04049198  
Dimple .068 Dia. Form Up .068 Dia. x .017 high .015 material 3.00 503 Mate #05084816  
Dimple .070 Rad. Form-Down .025 Deep .035 material 3.00 538    
Dimple .106 Dia. Form Up .106 Dia. x .025 high, for .036 Stainless 3.00 533 WT #569-8799, for 100-05771-01  
Dimple .170 Dia. Form-Up .050 High, relieved for 0.375 center to center between dimples. For .048 stainless 3.00 588 WT #740186-10 for 121518  
Dimple .205 Dia. Form-Up .050 High Relieved for 1.00 center to center between dimples. .035 material 3.00 397    
Dimple .213 Dia. Form-Down 0.213 Diameter 3.00 402    
Dimple R.63 Form-Up Dimple R.63 x .250 high for .090 Aluminum 3.00 736 WT #957775-10 for 508743-1 R-A  
Double Bridge Lance & Form (Form-Up) 0.059 wide Bridges x .079 high. Gap between bridges: .079", 0.866 length, for .062 material 3.00 631 WT #788810-10 for MOUNTING FRAM* R-  
Double Bridge Lance & Form (Form-Up) 0.079 wide Bridges x .100 high. Gap between bridges: .079", 0.550 length, for .048 material 3.00 832 WT # for 206-17326-01 R-A  
Emboss –NetD logo (tool 1) Form-Down Emboss the letters ‘Ne’ .030 deep in .060 material 3.00 299 Mate 10042905 For pn 7100-0016  
Emboss –NetD logo (tool 2) Form-Down Emboss the letters ‘tD’ .030 deep in .060 material 3.00 300 Mate 10042906 For pn 7100-0016  
Emboss – Obround Form-Down 0.582 x 2.238, .020 Deep, for .090 material 3.00 549 WT #582-4644 , for 7500-0015-00  
Emboss – Rectangle Form-Up 0.185 x 0.683 Rect. (flat area) x .080 High w/Rad corners. for .080 Alum. 3.00 457    
Emboss – Rectangle Form-Up 0.497 x 0.695 Rect. (flat area) x .098 High w/Rad corners. for .036 Stainless 3.00 940 WT #1407042-10 for 165004 R-A  
Emboss – Rectangle Form-Up 0.629 x 1.879 Rect. (flat area) x .025 High for .048 CR Steel 3.00 864 WT #1201193-10 for 45-40654 R-5  
Emboss – Rectangle Form-Down 1.000 x 0.730 Rect. x .010 deep w/Rad corners. For .062 Alum. 3.00 323 WT #372-1779 for p/n 2734217-0001  
Emboss – Rectangle Form-Up 45 Degree Form-Up Shape Emboss 45 Degree for 652-1572-02 3.00 473 WT# For 652-1572-02  
Emboss – Round Form-Up 0.152 ID x 0.050 deep .040 material W/Relief for .430 Centers 3.00 367    
Emboss – Round Form-Up 0.152 ID x 0.050 deep .059 material W/Relief for .430 Centers 3.00 426    
Emboss – Round Form-Up 0.197 ID x 0.043 deep .035 material 3.00 574 WT #699007-10 for 220353-00  
Emboss – Round Form-Down 0.200 ID x 0.020 deep .048 material W/Relief for .750 Centers 3.00 354 WT #398-4338 For McData I20K  
Emboss – Round Form-Up 0.200 ID x 0.020 deep .048 material W/Relief for .750 Centers 3.00 355 WT #398-4339 For McData I20K  
Emboss – Round Form-Up 0.250 ID flat area x .032 deep .030 material, W/Relief for .717 Centers 3.00 739 WT # for 115-00645-01  
Emboss – Round Form-Up 0.280 ID x 0.040 deep .035 material W/Relief for 1.33 Centers 3.00 970 WT #1494046-10 for 261-2560-00 R-B  
Emboss – Round Form-Down 0.375 ID x 0.011 deep .048 thick 3.00 307    
Emboss – Round Form-Up 0.380 ID flat area x .250 deep .048 material 3.00 825 WT# for 540-000141  
Emboss – Round (Form Down) 0.388 ID x .093 deep 059 material 3.00 356 Mate #09058162 Used on Redback 201-0436  
Emboss – Round Form-Up 0.400 ID x .115 deep for .035 material 3.00 408    
Emboss – Round Form-Up 0.500 ID x .025 deep .048 material 3.00 652 WT #831188-10 for 500-00174-00 R-03  
Emboss – Round Form-Up ~0.500 ID x 0.088 ID for .035 material .050 Inside radius .400 ID flat area 3.00 113    
Emboss – Round Form-Up ~0.560 ID x 0.070 ID for .050 material .032 Inside radius .500 ID flat area 3.00 112    
Emboss – Round Form-Up 0.563 ID x .120 deep .050 material 3.00 852 WT #1186309-20 for 209-11977-01 R-D  
Emboss – Round Form-Up 0.625 ID x 0.025 Deep for .048 material 3.00 425    
Emboss – Round Form-Up 0.630 ID flat area x .125 deep .062 material 3.00 899 WT #1312896-10 for 02422303-02 R-C  
Emboss – Round Form-Up 0.720 ID x .221 deep for .035 material 3.00 554 WT #585-4837 For 520-43092  
Emboss – Round Form-Up 0.750 ID x 0.060 Deep for .048 material 3.00 623 WT #776329-10 for 044-04-02-211  
Emboss – Round Form-Up 0.750 ID x 0.250 Deep for .080 material 3.00 404 WT #453-0398 used on B-B-V12 Chassis  
Emboss – Round Form-Down 0.827 ID flat area x .118 deep, .060 material 3.00 789 WT #1051801-20 for 520-48695-001 R-2  
Emboss – Round Form-Up 0.985 ID flat area x .198 high, .050 material 3.00 958 WT #1462714-10 for 520-49747-001 R-5  
Emboss – Round Form-Up 1.000 ID flat area x .157 high, .060 material 3.00 788 WT #1051801-10 for 520-48695-001 R-2  
Emboss – Special Form-Up (needs pre-punch on sides) Roof-Top 90° x .230 high for .090 material .030 Inside radius 3.00 223 Mate 12039126 used on p/n 40545  
Emboss – Special Rect w/Rad corners. Form-Up 2.070 x 1.820 w/Rad corners. 0.173 high O.D. for .048 material 3.00 320 WT #44-5396 used on p/n 56-00259-01  
Emboss – Square Form-Down 1.050 Square, with R.063 corners, .020 Deep, for .090 material 3.00 550 WT #582-4645 , for 7500-0015-00  
Extrusion (Form-Down) .078 I.D. .040 material 3.00 334    
Extrusion (Form-Up) .100 I.D. for .059 material 3.00 945 WT #1424059-10  
Extrusion (Form-Up) .100 I.D. for .048 material 3.00 513    
Extrusion for SS (Form-Up) .125 I.D. for .050 thick stainless 3.00 363 WT #413-7421  
Flattening Tool Letter Stamp-Form Down BOTTOM, Letter Stamp-Form Up TOP 3.00 757    
Formed C’sk (Form Up) 0.196 C’sk x 0.075 Deep x 72°, .089 thru hole, for .036 Stainless 3.00 532 WT # 569-8798 used on 100-05771-01  
Forming Tool – 90° (Form-Up) for McData Faceplate 90° Form-Up (needs prepunch) 1.952 Wide x 0.152 High O.D. .048 material 3.00 345 WT #388-6295 used on 002-002803  
Forming Tool – Eyelet (Form-Up). Stage 1 Tool 0.310 I.D. Eyelet. Tool #1 (.310 Extrusion). for .048 material 3.00 398 Mate #08069034 for 001-E03207-1P04  
Forming Tool – Eyelet (Form-Up). Stage 2 Tool 0.310 I.D. Eyelet. Tool #2 (Curl Down). for .048 material 3.00 399 Mate #08069035 for 001-E03207-1P04  
Forming Tool – F/U Lance & Form for 0480652 Form-Up Tab 0.100 Wide x 0.045 High I.D. .048 material 3.00 794 WT # for 0480652 R-C  
Forming Tool – F/U Lance & Form for 115-00603-01 Form-Up Tab 0.410 Wide x 0.322 High I.D. x 60 Degrees, for.048 material 3.00 606 WT #757384-10 for 115-00603-01  
Forming Tool – F/U Lance & Form for 115-00645-01 Form-Up Tab 0.056 Wide x 0.031 High I.D. x 25 Degrees, for .030 material 3.00 740 WT # for 115-00645-01  
Forming Tool – F/U Lance & Form for 500-00043-02 Form-Up Tab 0.070 Wide x 0.130 High I.D. .048 material 3.00 598 WT #748625-10 for 500-00043-02  
Forming Tool – Lance & Form for 701-1043-00 R-B 0.160 wide tab, includes 90-degree bend at one end, and 15-degree bend at other end. .032 material. 3.00 580 WT #706446-10 for 701-1043-000.  
Forming Tool – Progressive Stiffening Rib (Form-Up) 0.440 wide Progressive Stiffening Rib for .062 material 3.00 900 WT #1312896-20 for 02422303-02 R-C  
Forming Tool – Shovel Form for .024 Steel. Form-Up Shovel Form. 0.500 x 0.253 x 0.030 Gap, for .024 Steel. 3.00 582 WT #719331-10 for 60797 R-2  
Forming Tool – Tab (Form-Up) for McData Faceplate Form-Up Tab (needs prepunch) 0.335 Wide x 0.104 High I.D. .048 material 3.00 344 WT #388-6294 used on 002-002803  
Ground Symbol – Form Down, inside .310 circle .310 Diameter Ground Symbol, v-line steel stamp 3.00 478    
Ground Symbol – Form-Up, inside .380 circle .380 Diameter Ground Symbol 3.00 946 WT #1424380-30  
Ground Symbol – Form-Up, without circle Ground Symbol without Circle 3.00 947 WT #1424380-40  
Ground Symbol – Form-Down, inside .500 circle .500 Diameter Ground Symbol v-line steel stamp (.030 Deep) 3.00 859 WT #1191053-10  
Half-Shear Form-up 0.125 Diameter, 0 -.125 mat. 3.00 146 Mate 08031824  
Half-Shear Form-up 0.307 Diameter, 0 -.125 mat. 3.00 779 WT #1014483-10  
Hinge 3 Stage Hinge tool for .048 mat (2 tools – punches 2 knuckles at once) .500 knuckle, .100 ID 3.00 140, 141 Mate 05031007 Mate 05031008  
Keyway, Inside 0.197 +.000/-.001 Dia. Internal Keyway for .100 thick Alum 3.00 766 WT #994548-10 for 35002145-101  
Keyway, Inside 0.491 Diameter with 0.045 Wide x 0.040 Deep Inside Keyway 0.63 406    
Keyway, Inside 0.875 Diameter with R0.038 x 0.040 Deep Inside Keyway 3.00 814 Trumpf #T79-9777-1 for 1001-106-00  
Knock Out – Form Up Knock Out, 0.662 X 0.576 Rect - for .050 material, Form-Up 3.00 468 WT #522-0491 used on 100-05380-01  
Knock Out – Form Up .900 Square Knock Ou.t 0.900 Square on 1.15 Centers for .059 material 3.00 703 WT #895167-10  
Letter Stamp-short Form Down Form-Down. Short version. 2 rows x 10 char. Ea 3.00 373    
Letter Stamp. Form Down Form-Down. 2 rows x 20 char. ea 3.00 374    
Letter Stamp. Form Down Form-Down. 2 rows x 20 char. ea 3.00 437    
Letter Stamp. Form Up Form-Up. 2 rows x 20 char. ea 3.00 44    
Letter Stamp. Form Up Form-Up. 2 rows x 20 char. ea 3.00 364    
Letter Stamp. Form Up Form-Up. 2 rows x 20 char. ea 3.00 365    
Louver - Form Up 2.36 Long, .50 Wide, .25 High, for .100 material 3.00 430 Mate #11068007 used on 100-04996-02  
Louver - Form Up 3.50 Long, .500 Wide, .30 High for .090 Alum 3.00 535 WT #571-5288 for 090390  
Pedestal Tool – Rect. - Used with Emboss Tool #473 0.268 x 0.780 Rectangle. pedestal tool used with Emboss Tool #473 3.00 474 WT# For 652-1572-02  
Pedestal Tool – Round. Used with Emboss Tool #574 0.154 Round. Special pedestal tool used with Emboss Tool #574 3.00 575 WT #699007-20 for 220353-00  
Pedestal Tool – Round. Used with Emboss Tool #825 0.156 Round. Special pedestal tool used with Emboss Tool #825 3.00 826 WT #1125015-20 for 540-000141  
Pedestal Tool – Round. Used with Emboss Tool #320 0.169 Round. Special pedestal tool used with Emboss Tool #320 3.00 321 WT #44-5398 used on p/n 56-00259-01  
Pedestal Tool – Round. Used with Emboss Tool #408 0.177 Round Special pedestal tool used with Emboss Tool #408 3.00 409    
Pedestal Tool – Round. Used with Emboss Tool #404 0.265 Round. Special pedestal tool used with Emboss Tool #404 3.00 405 WT #453-0399 used on B-B-V12 Chassis  
Pedestal Tool – Sq. w/Rad corners.Used with Emboss #320 0.800 Square w/.130 Rad corners. Special pedestal tool used with Emboss Tool #320 3.00 322 WT #44-5400 used on p/n 56-00259-01  
Rectangle w/radius on 2 corners 1.155 x 1.210 w/ .125 radius on 2 corners (+.010 Die) 3.00 486 WT#525-7975 . Used on 40-10061  
Rectangle w/radius on 4 corners 0.105 x 0.250 w/ .024 radius on 4 corners (+.010 Die) 0.63 514    
Rectangle w/radius on 4 corners 0.133 x 0.822 w/ .017 radius on 4 corners (+.005 Die) 3.00 329    
Rectangle w/radius on 4 corners 0.295 x 0.580 w/ .031 radius on 4 corners (+.010 Die) 3.00 528    
Rectangle w/radius on 4 corners 0.406 x 0.425 w/ .031 radius on 4 corners (+.010 Die) 0.63 526    
Rectangle w/radius on 4 corners 0.472 x 0.630 w/ .079 Radius on 4 corners (+.006 Die) 3.00 626    
Rectangle w/radius on 4 corners 0.538 x 1.050 w/ .034 radius on 4 corners (+.005 Die) 3.00 125    
Rectangle w/radius on 4 corners 0.540 x 0.640 w/ .031 radius on 4 corners (+.010 Die) 3.00 527    
Special Coining Tool for ZHON Front Panels .570 x .529 x .020 Deep .048 Material for .533 Square pre-punch 3.00 336 Mate #06059003 Used on p/n 56-00284-01  
Special Coining Tool (Coin-Up) for LMQ Faceplate 0.024 x 45° Chamfer w/ 1.016 x 0.500 Rect. Pilot 3.00 362 WT #413-5208  
Special Shape - AURO 40-10463+ Special Shape .903 x 1.526 for .032 Aluminum 3.00 690 WT #871558-10 for 40-10463+  
Special Shape – AURO Connector 0.631 x 0.913 3.00 142 WT# 273-6095 273-6095.gif
Special Shape – AURO Keyhole Keyhole 0.240W x 0.136W x 0.388L 0.63 568 WT #690495-10 for 40-10461+ R-B  
Special Shape - Banana Tool 0.276 x 2.093 CL Radius for .125 material 3.00 480 Mate #12075032 for 970-000138  
Special Shape - Banana Tool 0.280 x 3.000 CL Radius for .134 material 3.00 596 Mate #06101569 for 400-17633-0001  
Special Shape - Banana Tool 0.394 x 3.000 CL Radius for .125 material 3.00 613 Mate #08102104 for 970-000185  
Special Shape - Banana Tool 0.406 x 1.375 CL Radius for .104 material 3.00 431 Mate #11067024 for 38000128  
Special Shape - Banana Tool 0.750 Radius Tool for .104 material 3.00 659 Trumpf #T57-7889-1  
Special Shape - Banana Tool 2.000 Radius Blanking Tool for .104 material 3.00 432 Mate #11067023 for 38000128  
Special Shape – Blanking Tool for 0118721 Blanking Tool – Save the Slug. For .090 steel. Curved Rect for 0118721 0.63 636 WT #801439-30 for 0118721  
Special Shape – Blanking Tool for 0450511 Blanking Tool – Save the Slug. For .030 steel. Curved Rect for 0450511 0.63 871 WT #1218812-10 for 0450511 R-D  
Special Shape – Blanking Tool for 0450514 Blanking Tool – Save the Slug. For .030 steel. Curved Rect for 0450514 0.63 883 WT #1250168-10 for 0450514 R-C  
Special Shape – Blanking Tool for 0450515 Blanking Tool – Save the Slug. For .030 steel. Curved Rect for 0450515 0.63 884 WT #1250168-20 for 0450515 R-B  
Special Shape – Blanking Tool for 0483874 Blanking Tool – Save the Slug. For .044 steel. Curved Rect for 0483874 3.00 664 WT #843481-10  
Special Shape – Blanking Tool for 0493278 Rect. 0.230 x 0.680 with Two .050 Rad. Corners. For .018 Stainless 3.00 616 WT #766356-30 for 0493278  
Special Shape – Blanking Tool for 050-211069-001 R-B Blanking Tool – Save the Slug. For .050 Stainless. 3.00 829 WT # For 020-211069-001 R-B  
Special Shape – Blanking Tool for 1002 R-A Blanking Tool – Save the Slug. For .025 Aluminum. 3.00 943 WT #1422664-10 for 1002 R-A  
Special Shape – Blanking Tool for 1066 R-A Blanking Tool – Save the Slug. For .020 Aluminum. 3.00 927 WT #1388616-10 for 1066 R-A  
Special Shape – Blanking Tool for 122089-001 R-B Rect. 0.623 x 0.187 with Radius 0.0585 For .015 Stainless 3.00 879 WT # for 122089-001 R-B  
Special Shape – Blanking Tool for 30A0056 R- Blanking Tool – Save the Slug. For .010 Steel, tack welded to thin sheet. 3.00 724 WT #936702-10 for30A0056  
Special Shape – Blanking Tool for 40-10001 Grnd Tab Blanking Tool – Save the Slug. Rect 0.625 x 1.437 (w/ rad 2x) for .075 CRS 3.00 491 WT #538-3048 For 40-10001 Grounding Tab  
Special Shape – Blanking Tool for 40-10190+ Blanking Tool – Save the Slug. For .030 thick steel. 3.00 651 WT #849817-10 for 40-10190+  
Special Shape – Blanking Tool for 40-10233+ R-B Blanking Tool – Save the Slug for .012 Brass 3.00 436 WT #888995-10 For 40-10233+  
Special Shape – Blanking Tool for 40-10470+ R-3 Blanking Tool – Save the Slug. For .024 steel. 3.00 872 WT #1225704-10 for 40-10470+ R-3  
Special Shape – Blanking Tool for 40-10684+ R-2 Blanking Tool – Save the Slug. For .062 Aluminum 3.00 905 WT # for 40-10684+ R-2  
Special Shape – Blanking Tool for 40-10869-01 R-A Blanking Tool – Save the Slug. 0.185 x 0.265 Rect w/.008 Rad corners. For .024 Stainless. 3.00 954    
Special Shape – Blanking Tool for 40-10869-02 R-A Blanking Tool – Save the Slug. 0.525 Square w/.008 Rad corners. For .024 Stainless. 3.00 955    
Special Shape – Blanking Tool for 40-10882 R-A Blanking Tool – Save the Slug. For .030 steel. 3.00 953 WT #1448457-10 for 40-10482 R-A  
Special Shape – Blanking Tool for 420-0171-00 R-B0 Blanking Tool – Save the Slug. For .063 Stainless. 3.00 950    
Special Shape – Blanking Tool for 452258 Blanking Tool – Save the Slug. For .035 steel. Curved Rect for 452258 0.63 619 WT #770393-10 for 452258  
Special Shape – Blanking Tool for 452259 Blanking Tool – Save the Slug. For .035 steel. Curved Rect for 452259 0.63 587 WT #738824-20 for 452259  
Special Shape – Blanking Tool for 510-43428 Blanking Tool – Save the Slug. For .006 Stainless. 3.00 687 WT #6784250 for 510-43428  
Special Shape – Blanking Tool for 80-10077+ R-A Blanking Tool – Save the Slug. For .035 thick Steel. 3.00 971 WT #1495289-10 for 80-10077+ R-A  
Special Shape – Blanking Tool for 80-10138+ Blanking Tool – Save the Slug. For .030 thick steel. 3.00 861 WT #1191632-10 for 80-10138+ R-1  
Special Shape – Blanking Tool for 900-2257-002 R-2 Blanking Tool – Save the Slug for .062 Aluminum. 3.00 795 WT #for 900-2257-002 R-2  
Special Shape – Blanking Tool for MLOCK CONTACT R- Blanking Tool – Save the Slug. For .035 Brass. Special Shape for MLOCK CONTACT R- 3.00 722 WT #932996-10  
Special Shape – Blanking Tool for R0024 R-01 Blanking Tool – Save the Slug for .0165 Aluminum. 3.00 770 WT #1006817-10 for R0024 R-01  
Special Shape – Blanking Tool for R0025 R-01 Blanking Tool – Save the Slug for .0165 Aluminum. 3.00 773 WT #1012338-10 for R0025 R-01  
Special Shape – Blanking Tool for S-0663-1 Blanking Tool – Save the Slug, for .024 stainless 3.00 506 WT #544-2664 , For S-0663-1  
Special Shape – Blanking Tool for S-0939 R-1 Rect. 26.6mm (1.0472") x 14.8mm (0.5827") with 4x Rad 1.95mm (R.0768") for .024 Stainless 3.00 849 WT # for S-0939 R-1  
Special Shape – Blanking Tool for S-0949 R-1 Rect. 28.575mm (1.125") x 15.075mm (.5935") with Rad 0.937mm (R.0369") for .024 Stainless 3.00 878 WT # for S-0949 R-1  
Special Shape – CARR left side for 2731228 Special Shape left side, with relief for .068 dimple. (overlaps with right side punch) 3.00 504 Mate #05084814  
Special Shape – CARR right side for 2731228 Special Shape right side, with relief for .068 dimple. (overlaps with left side punch) 3.00 505 Mate #05084815  
Special Shape – ConMed Radius 1.965 Radius on one edge. 0.479 Length. 0.375 Width at ends. 0.63 564 WT #689615-20 for 090378  
Special Shape- Connector for 2500000011919 0.449 x 0.753 10° Top, 0.449 x 0.740 0° Bottom, .126 Rad 3.00 640 WT #809978-10 for 2500000011919  
Special Shape- Connector for ENCLOSURE,SCBD 0.173 X 0.323 Special Shape Connector 0.63 806 WT #1108589-10 for ENCLOSURE,SCBD  
Special Shape – Curved Rectangle 0.394 Outside Rad x 68.72° .093 wide (.301 Inside Rad) 0.63 790 WT # for 220935-00 R-D  
Special Shape – Curved Rectangle 1.009 Outside Rad x 29° .401 wide (0.608 Inside Rad) 3.00 938 WT #1396697-10 for 221068-00  
Special Shape – Curved Rectangle 1.009 Outside Rad x 51.35° .401 wide (0.608 Inside Rad) 3.00 837 WT #1160868-20 for 220959-01 R-B & 220988-00 R-B  
Special Shape – Curved Rectangle 1.526 Outside Rad x 29° .391 wide (1.134 Inside Rad) 3.00 937 WT #1396697-20 for 221068-00  
Special Shape – Curved Rectangle 1.526 Outside Rad x 51.35° .391 wide (1.134 Inside Rad) 3.00 836 WT #1160868-10 for 220959-01 R-B & 220988-00 R-B  
Special Shape – Curved Rectangle 2.378 Outside Rad x 14.7° .253 wide (2.125 Inside Rad) 0.63 808 WT #1108654-21  
Special Shape – Curved Rectangle Curved Rect w/rad corners. For FINI 1077712 3.00 534 WT #571-0991 for 1077712 571-0991.bmp
Special Shape – Fan Opening for 100-05739-03 Special Shape per drawing 100-05739-03. For .048 material. 3.00 669 WT #854254-10 for 100-05739-03  
Special Shape - fan punch   3.00 71 T276047 t276047.gif
Special Shape – FINI Blanking Tool Blanking Tool for FINI 3.00 244 WT# 322-8930 322-8930.gif
Special Shape for p/n 10258-FP-B 0.174 x 0.324 Rect with Rad 2x & Chamfer 2x 0.63 733 WT # for 10258-FP-B  
Special Shape for p/n 115-00645-01 Special Shape 0.136 x 0.325 0.63 737 WT # for 115-00645-01  
Special Shape for p/n 970-000138 Special Shape 3.00 964 WT #1483728-10 for 970-000138  
Special Shape – Half Circle 0.150 x 0.300 Half Circle 0.63 778 For 40-AT3CX-COVER R-1  
Special Shape – House shape (partial Hex) 0.072 wide x 0.125 high. House-Shape for GRAN. 0.63 542 WT #578-5213 for G747-0005A  
Special Shape- METR Blanking Tool Special Shape per drawing 72-71-731 Rev.A .080 Material 3.00 295 WT# 347-8966  
Special Shape – QUAN 850-0608-00Z Special Shape for QUAN 850-0608-00Z R-02 for .015 Stainless 3.00 714 WT #924590-10 for 850-0608-00Z R-02  
Special Shape – RADI Blanking Tool 0.324 x 0.519 Rectangle w/ 45-Degree chamfer on 2 corners 0.63 283 WT # 338-8456 (For Y18-0010)  
Special Shape – Radius for 0505128 C Shaped Radius Tool for R.160 3.00 866 WT #1215383-10 for 0505128 R-  
Special Shape – SALI semitrapezoid 0.186 x 0.793 3.00 135 WT# 269-1167 269-1167.gif
Special Shape – Tab for 80-10070+ J-Shape partial Tab for 80-10070+ R-A 3.00 797 WT #1076671-20 for 80-10070+ R-A  
Special Shape – Tab for 80-10076+ J-Shape partial Tab for 80-10076+ R-A 3.00 966 WT # 1484114-10 for 80-10076+  
Special Shape – Trapezoid (partial Hex) 0.063 wide x 0.144 long. trapezoid for GRAN. 0.63 541 WT #578-5212 for G747-0005A  
Special Shape – Trapezoid with Radius Corners 0.121 wide x 0.176 long Trapezoid w R.010 on all corners 0.63 600 WT #750993-10 for 540-000043  
Square w/Rad corners 0.250 w/.030 Rad on 4 corners 0.63 379    
Square w/Rad corners 0.290 w/.060 Rad on 4 corners 0.63 523    
Square w/Rad corners 0.300 w/.052 Rad on 4 corners 0.63 427    
Square w/Rad corners 0.300 w/.062 Rad on 4 corners 0.63 139    
Tapping Tool   3.00 57    
Trapezoid 0.250 x 0.750 3.00 78 T310953 t310953.gif
Triangle 0.151 X 0.200 3.00 552 For G749-0002  


back to top | back to overview | Printversion| .xls-download